|
|
|
|
|
|
Malco CB Replacement Cutter Bit, For Use With Cutter, 6-1/2 in Length, 1/4 in Diameter Shank
|
|
|
Mill type cutter bit for HC1 (373.8515) and HC2.
|
|
|
|
|
|
|
|
|
|
Wiss WC5L Crimper Blade 1-5/8 in D Jaw, Galvanized Steel Jaw, Non-Slip Cushion Grip
|
|
|
Optimal handle span for maximum power and comfortable operating range; non-slip cushion grips for superior comfort and control; for crimping round metal pipe to create a male fitting end; crimps heavier gauge pipe up to 22 gauge galvanized steel. Throat depth is 1-5/8".
|
|
|
|
|
|
|
|
|
|
Malco 18F Fixed Folding Tool, Steel
|
|
|
Tool with 3/8" (9.5 mm) & 1" (25.4 mm) depths. Folding seams are formed from two steel halves, permanently joined together. Handy sight holes assure proper depth alignment. Longer folding tool assures a more uniform fold. Length 18".
|
|
|
|
|
|
|
|
|
|
Wiss WC5S 5-Blade Hand Crimper, 1-1/4 in W X 1-1/4 in D Jaw, Cushion Grip
|
|
|
Crimps for heating, ventilating and air conditioning. Made from quality steel for better edges with a treated industrial finish to help prevent rust. Cushion grip handles. Use for joining sheet metal pipes of the same size [can be corrugated, round or square] or repairs in the field. Matte black finish and red plastisol grips. Compound action. Throat depth is 1-1/4"; length is 9-1/4".
|
|
|
|
|
|
|
|
|
|
Wiss WT1 Cable Tie Tensioning Tool, Heavy and Light Duty Nylon Cable Tile, 7-1/2 in L
|
|
|
Designed to install both heavy and light duty nylon cable ties; for tightening nylon ties when securing flex duct to take-off collars; easy to operate cut-off mechanism that trims excess cable strap; comfortable cushion grip handles and internal stop.
|
|
|
|
|
|
|
|
|
|
Wiss WS3 HVAC Hand Seamer, 3 in W X 1-1/4 in D Jaw, 8-3/4 in OAL, Forged Steel
|
|
|
Produces a permanent tight fitting seam. Compound action jaw with 1/4" incremental depth marks on jaw. Jaw of finest quality steel for better edges and long life. Rust resistant blades with cushion handle for all weather comfort. Matte black finish and red plastisol grip. Throat depth is 1-4" to 1-1/4"; length is 8-3/4".
|
|
|
|
|
|
|
|
|
|
Wiss WS4 Hand Seamer, 3-1/4 in W, 9 in OAL
|
|
|
1/4" depth markings; optimal handle span for maximum power and comfortable operating range; non-slip cushion grips for superior comfort and control; 3-1/4" jaw width and 1-1/4" maximum seam depth; used to bend and flatten sheet metal.
|
|
|
|
|
|
|
|
|
|
Wiss WHN1 Hand Notcher 8-3/4 in L, Gray Non-Slip Cushion Grip
|
|
|
Cuts 30 degree V shaped cut in sheet metal; non-slip cushion grips for superior comfort and control; gives clean notch without slipping at corners and take-off tabs. Throat depth is 13/16".
|
|
|
|
|
|
|
|
|
|
Wiss WS6 Hand Seamer, 6 in W, 9-1/4 in OAL
|
|
|
1/4" depth markings; optimal handle span for maximum power and comfortable operating range; non-slip cushion grips for superior comfort and control; 3-1/4" jaw width and 1-1/4" maximum seam depth; used to bend and flatten sheet metal.
|
|
|
|
|
|
|
|
|
|
Redline S9R Hand Seamer, 9 in W X 2 in D Jaw, Die-Cast Zinc
|
|
|
Makes clean and accurate angle bends for aluminum roof flashing, coil stock or fascia. Jaws feature depth graduations in 1/4" (6.4 mm) increments to a maximum 2" (50.8 mm) bending depth. Lightweight die cast zinc jaws with compound handle leverage for comfort. Tool also features rust resistant nickel plating. Non-slip vinyl grips with hand stops provide added comfort and control. Ergonomic REDLINE handles with unique one hand operation latch. Jaw width is 9"; Jaw depth is 2".
|
|
|
|
My cart:
